The MAX20079 is a small, automotive grade synchronous buck converter with integrated high-side and low-side switches. The device is designed to deliver up to 3.5A with input voltages from +3V to +36V while using only 3.5μA quiescent current at no load.
The MAX3080-MAX3089 high speed transceiver for RS-485/RS-422 communication contains a driver and a receiver. All devices have 1/8 cell load receiver input impedance, allowing up to 256 transceivers on the bus. MAX3082 MAX3085 / MAX3088 for half duplex communication, and MAX3080 / MAX3081 / MAX3083 / MAX3084 MAX3086 / MAX3087 for full-duplex communication. The MAX3089 can be selected between half duplex and full duplex. It also features a separate programmable receiver and emitter output phase through separate pins.
Maxim Integrated's MAX22502EATC+ is a full-duplex, ESD-protected RS-485/RS-422 transceiver that can be optimized for high-speed (up to 100 Mbps) communication over long cables. The transceiver has high noise suppression and improved signal integrity
Maxim's MAX98390 is a highly efficient single Class d DSM intelligent amplifier with integrated boost converter, integrated DSM and FET calibration capabilities to achieve higher efficiency at low output power. Maximum boost converter output voltages can be programmed from 6.5V to 10V, with 0.125V increments from battery voltage down to 2.65V.
The Maxim MAX14874 Evaluation Kit is a fully assembled and tested circuit board for evaluating the MAX14874 dual relay/valve/motor driver. The kit is powered by a single supply from 4.5V to 36V and features a linear voltage regulator to produce a 3.3V logical power supply. The MAX14874 kit has terminal blocks that can be easily connected to evaluate the operation of relays, valves or motors.
Maxim Integrated's MAX30001CWV+ is an analog front-end (AFE) solution that includes biopotential and Bioimpedance (BioZ) for wearable applications. The solution is designed specifically for fitness and clinical applications and will extend battery life due to high performance and ultra-low power consumption. It is available in a 30 WLP and can operate in the temperature range of 0°C to +70°C.
Maxim Integrated's MAX86150 provides pleural graph (PPG) and electrocardiogram (ECG) measurements via a mobile battery-powered device for health monitoring. The MAX86150 is a biosensor module consisting of an internal light-emitting diode, photodetector, and ECG analog front end (AFE) that delivers highly accurate, FDA-approved PPG and ECG performance in compact power-saving designs that include mobile phones, laptops, tablets, and smart speakers.
Maxim Integrated's MAX32672 is an ultra-low-power, highly integrated, cost-effective, and highly reliable 32-bit microcontroller that allows the design of complex sensor processing without compromising battery life. It combines a flexible and versatile power management unit with a powerful Arm Cortex-M4 processor with FPU.
Security has become a top priority in the IoT era, especially at the hardware level. Maxim hopes to bring both security and low power consumption to IoT applications with its cryptographic processors. Maxim Integrated (now officially part of ADI) has been working hard to accomplish this. The company has released a new low-power cryptographic controller that leverages Physical Unclonable Function (PUF) technology to improve hardware security.
Mouser currently offers Maxim Integrated Products' MAX25530 four-channel automotive backlight drive. The device integrates a positive boost converter, a negative boost converter, two charge pump drivers for TFT bias power supply, and a Boost /SEPIC controller.
Maxim Integrated Products' MAX78000 Ultra-low power neural network microcontroller uses Xailient's proprietary Detectum neural network to detect and locate faces in video and images. The company's microcontrollers are paired with Xailient's neural network to improve the overall power efficiency and battery life of the edge/cloud hybrid application. Xailient's Detectum neural network, which includes focus, zoom and visual wake word technologies, detects and locates faces in video and images 76 times faster and with similar or higher accuracy than traditional software solutions
Maxim Integrated Products has released a four-channel low-voltage MAX25512 automotive LED backlight driver with an Integrated boost converter. It maintains full, constant brightness of the in-car display at 3V input voltage, even under extremely cold crank conditions. The device integrates a boost converter and current detection resistor, eliminating the external MOSFEts typically needed to drive car displays. Available in a small 24-pin, 4mm x 4mm x 0.75mm QFN package, the solution is reduced in size by 30% by eliminating external components.
The MAX38889 has a 94% peak efficiency, 9% higher than recent competing solutions, allowing it to support longer backup times. In applications such as smart meters or car dashboard cameras, regulators operate in step-down mode to charge backup power sources such as supercapacitors.
The Maxim Integrated MAX25250 Four Output Mini PMIC is an efficient four-output PMIC that combines three DC-DC converters and a high PSRR LDO designed for camera applications. OUT1 is A 1A high voltage synchronous buck converter. OUT2 and OUT3 low voltage synchronous buck converters work from OUT1. OUT2 provides 1.2a for high pixel cameras and high speed serializers. OUT3 provides 1.2a to power the imager, serializer, and MCU secondary rails. The OUT4 is a low voltage, low noise, high PSRR imaging power LDO.
Maxim Integrated Products has released the MAXREFDES178# camera cube reference design, demonstrating how AI applications previously restricted to machines with large power and cost budgets may be embedded in space-constrained, battery-powered edge devices. The design facilitates ultra-low-power IoT devices to implement hearing and vision and showcases the MAX78000 low-power microcontroller with neural network accelerator for audio and video inferences.
Maxim MAX25410 USB PD Port Protector, available now from Mouser, is an automotive USB-PD-based Type-C protection solution for automotive radio, navigation, connectivity, and USB hub/multimedia module applications.
Maxim Integrated MAX20333 Adjustable Current-Limit Switches feature internal current limiting to stop damage to host devices due to faulty load conditions.
Maxim’s MAX32558 DeepCover IC enables faster and simpler design of robust security capabilities into industrial, consumer, computing and IoT applications.
