The LP2950-N and LP2951-N are micropower voltage regulators with very low quiescent current (75 µA typical) and very low dropout voltage (typical 40 mV at light loads and 380 mV at 100 mA). They are ideally suited for use in battery-powered systems. Furthermore, the quiescent current of the device increases only slightly in dropout, prolonging battery life.
The LFXX is a very low drop regulator available in TO-220, TO-220FP, DPAK and PPAK packages and in a wide range of output voltages. The low drop voltage (0.45 V) and low quiescent current make it particularly suitable for low-noise, low-power applications and especially in batterypowered systems.
The SC4215 is a high-performance positive regulator designed for applications requiring very low input voltage and very low voltage drop (up to 2 amps). Its Vin voltage is as low as 1.6V, and its output voltage is programmable as low as 0.8V. The SC4215 has an ultra-low drop out, which is very suitable for Vout applications that are very close to Vin
The LP5900 is an LDO capable of providing 150 ma output current. The LP5900 device is designed specifically to meet the requirements of RF and analog circuits with low noise, high PSRR, low static current, and low line transient response diagrams. Using new and innovative design technology, the LP5900 provides best-in-class device noise performance with no noise bypass capacitors.
The LM22671 switch regulator provides all the necessary features to achieve effective high voltage step-down (step-down) regulators using a minimum of external components. This easy-to-use regulator incorporates a 42 V n-channel MOSFET switch capable of delivering load currents up to 500 mA. TI's WEBENCH tool includes features such as external component calculations, electrical simulation, thermal simulation and easy-to-design Build-It boards.
The LMH0034 SMPTE 292M / 259M Adaptive cable Equalizer is a monolithic integrated circuit designed to equalize data transmitted over a cable (or any medium with similar dispersion loss properties). Equalizers are flexible, allowing single-ended or differential input drives.
The Intersil ISL95311 is a digitally controlled potentiometer (XDCP). The device consists of a resistor array, wiper switches, a control section, and nonvolatile memory. The wiper position is controlled by an I2C interface.
The ACPL-W611/ACPL-P611 is an optically coupled gate that combines a GaAsP light emitting diode and an integrated high gain photo detector. The output of the detector IC is an open collector Schottky clamped transistor. The internal shield provides a guaranteed common mode transient immunity specification of 10,000 V/μs for the ACPL-W611
The ISL28110, ISL28210, are single and dual JFET amplifiers featuring low noise, high slew rate, low input bias current and offset voltage, making them the ideal choice for high impedance applications where precision and low noise are important. The combination of precision, low noise, and high speed combined with a small footprint provides the user with outstanding value and flexibility relative to similar competitive parts
The ISL3259E is a ±15kV IEC61000 ESD Protected, 5V powered, single transceiver that meets both the RS-485 and RS-422 standards for balanced communication. It also features the larger output voltage and higher data rate (up to 100Mbps) required by high speed PROFIBUS applications. The low bus currents (+220µA/-150µA) present a 1/5 unit load to the RS-485 bus.
The ADR42x are a series of ultraprecision, second generation eXtra implanted junction FET (XFET) voltage references featuring low noise, high accuracy, and excellent long-term stability in SOIC and MSOP footprints.
The MAX6316 - MAX6322 family of manpower (μP) supervisory circuits monitors power supplies and manpower activity in digital systems. It offers several combinations of push/pull, open-drain, and bidirectional (such as Motorola 68HC11) reset outputs, along with watchdog and manual reset features.
This device is fabricated using LinCMOS technology and consists of two independent voltage comparators. each designed to operate from a single power supply. Operation from dual supplies is also possible if the difference between the two supplies is 1.4V to 18 V. Each device features extremely high input impedance (typically greater than 1012 Ω), which allows direct interface to high-impedance sources.
The LM2576 series of regulators are monolithic integrated circuits ideally suited for easy and convenient design of a step−down switching regulator (buck converter). All circuits of this series are capable of driving a 3.0 A load with excellent line and load regulation. These devices are available in fixed output voltages of 3.3V, 5.0V, 12V, 15V, and an adjustable output version.
The AT28C256 is a high-performance electrically erasable and programmable readonly memory. Its 256K of memory is organized as 32,768 words by 8 bits. Manufactured with Atmel's advanced nonvolatile CMOS technology, Organized as 32,768 words by 8 bits. Manufactured with Atmel's advanced nonvolatile CMOS Technology, the device offers access times to 150 ns with power dissipation of just 440 mW. When the device is deselected, the CMOS standby current is less than 200 µA.
The MIC94060, MIC94061, MIC94062, and MIC94063 are high-side load switches designed for operation between 1.7V to 5.5V. The devices contain a low on-resistance P-channel MOSFET that supports over 2A of continuous current. The MIC94061 and MIC94063 feature an active load discharge circuit which ensures capacitive loads retain no charge when the main switch is in an OFF state.
The MIC2954 is an efficient voltage regulator with very low dropout voltage (typically 40 mV at light loads and 375 mV at 250 mA), and low quiescent current (120 µA typical). The quiescent current of the MIC2954 increases only slightly in dropout, thus prolonging battery life. Key MIC2954 features include protection against reversed battery, fold-back current limiting, and automotive load dump protection (60V positive transient).
The LT3014B is a high voltage, micropower low dropoutlinear regulator. The device is capable of supplying 20mA of output current with a dropout voltage of 350mV. Designed for use in battery-powered or high voltage systems, the low quiescent current (7µA operating) makes the LT3014B an ideal choice. Quiescent current is also well controlled in dropout.
